On this page
Mold Removal Services Near You in Bloomington, California
The goal of mold removal is to find what is feeding the mold, seal off the work area, remove the contaminated material and clean the air. Bloomington sees seasonal swings in humidity and temperature. Winter condensation, spring thaw and summer storms are the usual triggers for attic, basement and window-sill mold.
- Mold inspection in Bloomington: visual check plus a moisture meter, thermal camera and borescope to find hidden growth.
- Mold testing in Bloomington: air and surface samples sent to a lab, and clearance testing after removal.
- Black mold removal: containment and removal of Stachybotrys and other toxic mold on drywall, wood and insulation.
- Water damage mold remediation: drying, dehumidification and mold removal after floods, leaks and burst pipes.
- Attic, basement and crawl space mold removal, plus mold in bathrooms, walls and HVAC ducts.
- Emergency and same-day mold removal: call to ask about the earliest inspection time in Bloomington.
How Much Does Mold Removal Cost in Bloomington, CA?
The national average for mold remediation is about $2,250 to $2,400, and most homeowners pay between roughly $1,100 and $3,500. Pricing runs about $10 to $25 per square foot of affected area, or $15 to $30 when the mold is hidden or hard to reach. Cost guides differ, so treat these as estimates. Cost guides report California pricing running about 30 to 50 percent above the national range.
Ranges below are adjusted for the Riverside-San Bernardino-Ontario area, where construction-labor wages put typical prices about 14% above the national range (BLS wage data, May 2025). It is an estimate from wages, not a local quote.
| Job | Typical cost | Time |
|---|---|---|
| Mold inspection | $350 – $900 | 2 – 4 hours |
| Air or surface mold testing | $300 – $700 plus lab fees | 1 – 2 hours + lab time |
| Small area under 10 sq ft | $550 – $1,700 | 1 day |
| Bathroom mold removal | $550 – $2,300 | 1 day |
| Basement mold removal | $1,700 – $4,600 | 2 – 4 days |
| Crawl space mold removal | $1,100 – $5,700 | 2 – 4 days |
| Attic mold removal | $1,100 – $6,800 | 1 – 2 days |
| Mold inside walls (drywall removal) | $1,100 – $9,100 | 2 – 4 days |
| Air duct mold cleaning | $700 – $2,300 | 1 day |
| HVAC system mold | $3,400 – $11,500 | 1 – 3 days |
| Whole house or severe black mold | $11,500 – $34,000+ | 1 week or more |
| Clearance (post-removal) testing | $250 – $700 | 1 – 2 hours + lab time |
Cost by size of the affected area
| Affected area | Typical cost |
|---|---|
| Under 10 sq ft | $550 – $1,700 |
| 10 – 100 sq ft | $1,700 – $5,700 |
| 100 – 300 sq ft | $2,800 – $10,500 |
| 300 – 1,000 sq ft | $6,800 – $23,000 |
Rebuild and root-cause add-ons
Remediation quotes usually exclude rebuilding, so budget for it separately.
| Add-on | Typical cost |
|---|---|
| Drywall replacement | $500 – $2,000 per room |
| Insulation replacement | $500 – $2,500 |
| Flooring replacement | $1,000 – $5,000 |
| Painting after drywall repair | $300 – $1,200 |
| Dehumidifier | $200 – $1,500 |
| Crawl space vapor barrier | $1,500 – $5,000 |
| Sump pump | $600 – $2,500 |
| Interior waterproofing | $3,000 – $8,000 |
What changes the price
- Square footage, and how deep the mold goes into drywall, wood or insulation
- Hidden mold behind walls or in tight crawl spaces and attics
- Containment, negative air and HEPA equipment, roughly 5 to 10 percent of a typical quote each
- Labor, which is often 50 to 65 percent of the total
- Black mold, which some guides price 10 to 25 percent higher
- Whether the leak or moisture source is already fixed, and California licensing and clearance testing rules
The Mold Removal Process
- Inspection and moisture mapping. Find every wet and moldy area and the leak behind it.
- Containment. Seal the work area with poly sheeting and run negative air so spores stay out of the rest of the house.
- HEPA air filtration. Air scrubbers capture airborne spores during the job.
- Removal. Cut out porous material such as drywall and insulation, then HEPA-sand and vacuum structural wood.
- Cleaning and drying. Antimicrobial cleaning, then dehumidifiers until moisture readings are normal.
- Clearance testing and repair. Confirm spore counts are back to normal, then rebuild.
Common Types of Mold in Bloomington Homes
Molds are grouped by the moisture they need, measured as water activity (1.0 is pure water). Primary colonizers grow on slightly damp surfaces. Tertiary colonizers need soaked material, so finding them points to serious water damage.
| Mold | Minimum water activity | Colonizer | Notes |
|---|---|---|---|
| Aspergillus | about 0.77 – 0.96 | Primary | Common in dust, HVAC systems and insulation |
| Penicillium | 0.78 – 0.88 | Primary | Blue-green growth on water-damaged carpet and wallpaper |
| Cladosporium | 0.85 – 0.88 | Secondary | Olive or black spots on window sills, fabrics and cabinets; linked to asthma in damp homes |
| Alternaria | 0.85 – 0.88 | Secondary | Common airborne allergen |
| Fusarium | 0.87 – 0.91 | Secondary | Seldom found indoors; some species make mycotoxins |
| Chaetomium | above 0.90 | Tertiary | Indicator of water damage |
| Stachybotrys chartarum (black mold) | 0.94 or higher | Tertiary | Slimy greenish-black growth on wet drywall paper, ceiling tile and wood; needs about 48 hours or more of sustained wetness |
Signs You Need Mold Removal in Your Bloomington Home
If one or more of these show up in your Bloomington home, schedule a mold inspection soon.
- A musty, earthy smell that gets stronger when the HVAC runs
- Coughing, sneezing, itchy eyes or asthma that improves when you leave the house
- Black, green, white or orange spots on walls, ceilings, grout or around windows
- Condensation on windows or a damp feeling in closets and basements
- Water stains, bubbling or peeling paint, warped drywall or flooring
How to Choose a Mold Removal Company in Bloomington
- Confirm general liability insurance.
- Check references and ask for the company to follow EPA mold guidance and IICRC S520.
- Ask how they will find and fix the moisture source.
- Ask whether clearance testing is included, and who performs it. An independent tester avoids a conflict of interest.
- Get at least two itemized written quotes that name the moisture source, containment, removal and clearance criteria.
Credentials to look for
- IICRC certified firm with technicians holding the Applied Microbial Remediation Technician (AMRT) credential, which requires Water Damage Restoration Technician (WRT) certification first.
- IICRC Mold Remediation Specialist (MRS), which requires at least 12 months of documented field experience.
- ACAC certifications, which require documented years of field experience and an exam.
- The EPA does not certify mold companies. California has no statewide mold license, so credentials and insurance matter more.
Red flags: no inspection before the quote, a "fogging" only plan, no containment, claims that all mold can be removed, full payment up front, no certificate of insurance, pressure to sign the same day.
Mold Removal Methods: What Works and What Does Not
- Physical removal works. HEPA vacuuming, damp wiping and discarding porous material remove the mold itself. The EPA stresses that dead mold is still allergenic, so killing it is not enough.
- Biocides and bleach are not routine. The EPA does not recommend them as a standard step. The CDC says use no more than 1 cup of bleach per gallon of water on hard surfaces only, and never mix bleach with ammonia.
- Ozone generators do not fix mold. The EPA says ozone at safe levels does not effectively remove mold, and the levels needed would be 5 to 10 times health limits.
- Fogging is disputed. Critics say it only covers surfaces and leaves the growth source. Some vendors and one Army engineering study report benefits. Ask any Bloomington contractor who proposes fogging to explain what is being removed.
- Painting over mold fails. The paint peels and the mold keeps growing underneath. Mold-resistant paint helps prevent new growth but does not clean existing mold.
| Method | Typical added cost |
|---|---|
| Fogging only | $400 – $800 |
| Sanding or wire brushing | $1,000 – $3,000 |
| Dry ice blasting | $3,000 – $8,000 |
A whole-house quote under $800 usually means fogging only and no removal.
Does Insurance Cover Mold Removal in California?
Homeowners insurance generally treats mold as a maintenance issue, but it often pays when mold follows a covered event such as a burst pipe or storm damage. Many policies cap mold payouts, commonly at about $1,000 to $10,000, and some endorsements raise the cap to $25,000. Flood insurance through the NFIP generally excludes mold remediation, and renters policies usually exclude mold from neglect or flooding. Report water damage right away, photograph everything and keep receipts.
California has no state license for mold inspectors or remediators and has set no mold exposure limits, according to the Department of Public Health.
California sellers must disclose known mold on the Transfer Disclosure Statement (Civil Code 1102.6).
DIY Mold Cleanup vs Professional Mold Removal
| DIY | Professional | |
|---|---|---|
| Best for | Under 10 sq ft on hard surfaces | Over 10 sq ft, drywall, ducts, flood or sewage water |
| Cost | $20 – $100 in supplies | $500 – $6,000+ |
| Containment and HEPA | No | Yes |
| Fixes the moisture source | Rarely | Yes, as part of the scope |
| Clearance testing | No | Available |
Skip bleach on porous materials like drywall and wood, since it does not reach roots below the surface.
Health Effects of Mold in Bloomington Homes
The CDC lists a stuffy nose, sore throat, coughing or wheezing, burning eyes and skin rash as the usual reactions to indoor mold. People with asthma or mold allergy can react more strongly, and people with weakened immune systems or chronic lung disease can develop lung infections.
- Is black mold more dangerous? Not by color. NIOSH says color does not indicate how dangerous a mold is, and the CDC says all molds should be treated the same for risk and removal. Some molds, including some Stachybotrys strains, can produce mycotoxins, but research has not established "toxic mold syndrome".
- Damp buildings. The World Health Organization found enough evidence that people in damp or moldy buildings have more respiratory symptoms, respiratory infections and asthma flare-ups.
- No safe numeric limit. There are no health-based federal standards for mold levels, so a clean result means the building looks like the outdoors, not that a number was met.
- See a doctor about symptoms, and ask a contractor to inspect the home.
When to Call a Pro: Mold Removal by Size of the Area
The EPA sorts mold jobs by the size of the affected area. The same tiers decide how much containment and protective gear a Bloomington job needs.
| Affected area | Containment | Protective gear | Who handles it |
|---|---|---|---|
| Under 10 sq ft (about 3 ft × 3 ft) | None needed | N-95 mask, gloves, goggles | Many homeowners can clean it |
| 10 to 100 sq ft | Limited: one layer of 6-mil polyethylene, sealed vents and doors | HEPA half-face or full-face respirator, disposable overalls | Experienced contractor recommended |
| Over 100 sq ft, or heavy exposure | Full: double polyethylene layers with a decontamination airlock | Full-face respirator or powered air-purifying respirator, mold-impervious coveralls | Experienced contractor |
Under negative air, the plastic sheeting should billow slightly inward. If it flutters or bulges outward, the containment is not working.
How to Prevent Mold in Bloomington Homes
- Keep indoor humidity between 30% and 50%, and never above 60%.
- Fix leaks and dry wet materials within 24 to 48 hours.
- Run bathroom and kitchen exhaust fans to the outside, not into the attic.
- Replace caulk and grout that cracks around tubs and showers.
- Use a dehumidifier in basements and crawl spaces.
What Gets Cleaned and What Gets Thrown Out
How a material is treated depends on how porous it is. Mold grows into porous materials, so they are usually removed. Hard surfaces can be cleaned.
| Material | Typical treatment in Bloomington |
|---|---|
| Drywall and ceiling tile | Cut out and discarded when mold has grown into it |
| Carpet and padding | Usually discarded |
| Insulation | Removed and replaced when wet or moldy |
| Wood framing | Cleaned in place by wet vacuuming, damp wiping and HEPA vacuuming; sanding is also common. Rotted wood is replaced |
| Concrete | Wet vacuumed and HEPA vacuumed |
| Tile, glass, metal and other hard surfaces | Scrubbed with detergent and water, then dried fully |
| Painted walls | Cleaned and dried first. Painting over mold tends to peel |
Water Damage and Mold: How Fast to Dry Out
Mold needs moisture. The EPA says materials dried within 24 to 48 hours of a leak usually do not develop mold. Keep indoor humidity below 60 percent, ideally 30 to 50 percent (the CDC advises no higher than 50 percent). Before rebuilding, contractors commonly dry wood framing to roughly 16 to 20 percent moisture content, and sources differ on the exact target.
| Water type | Meaning | Mold risk in Bloomington |
|---|---|---|
| Category 1 | Clean water from a supply line or rain | Low if dried fast; rises after 48 hours |
| Category 2 | Gray water from washers or dishwashers | Moderate; contaminated materials usually removed |
| Category 3 | Sewage or flood water | High; professional cleanup required |
Water damage is also rated by class from 1 to 4, depending on how much material is wet and how slowly it dries. Class 2 means a whole room including carpet, and class 3 means water from above that has soaked ceilings, walls and insulation.
Mold Inspection and Mold Testing in Bloomington
Before pricing a Bloomington mold job, a good inspector maps moisture first and samples second. Inspectors use moisture meters, thermal imaging cameras and borescopes to find hidden growth, then take air or surface samples when needed. The EPA says sampling is generally unnecessary when mold is visible, and the CDC does not recommend routine testing, so testing is most useful when mold is suspected but hidden, after water damage, or to verify cleanup. A typical residential test with a few indoor samples and an outdoor control costs about $300 to $700, with individual spore-trap samples around $100 to $200 and ERMI dust tests about $250 to $500. Clearance testing after removal confirms the work area matches outdoor mold types and levels, with the moisture fixed and no visible mold or odor.
Where Mold Grows in Bloomington Homes
Where you find mold tells you what is leaking, condensing or ventilating badly. Here is what we see in CA homes.
Mold after water damage, flood or leak
Wet drywall, carpet and insulation grow mold in 24 to 48 hours. Fast drying with air movers and dehumidifiers prevents a larger removal job.
HVAC and air duct mold
Condensation in ducts and drain pans spreads spores through every room. Duct cleaning and a fixed drain line stop the cycle.
Basement and crawl space mold removal
Groundwater, high humidity and uninsulated pipes cause mold on walls, joists and stored items. Fixes include drainage, a vapor barrier and a dehumidifier.
Attic mold removal
Poor ventilation and bathroom fans vented into the attic cause roof sheathing mold. Pros HEPA-vacuum and clean the wood, then correct the ventilation.
Bathroom mold removal
Steam, weak exhaust fans and wet grout feed mold on ceilings, caulk and behind tile. Removal means cleaning hard surfaces and replacing wet drywall or caulk.
Mold Removal in Bloomington FAQs
How much does mold removal cost in Bloomington, CA?
The national average for mold remediation is about $2,250 to $2,400, and most jobs in Bloomington fall between roughly $1,100 and $3,500, or about $10 to $25 per square foot of affected area. A small area under 10 square feet is usually $500 to $1,500, a bathroom $500 to $2,000, and an attic $1,000 to $6,000. Severity, hidden mold, containment and drywall replacement change the final price. Local labor costs in the Riverside-San Bernardino-Ontario area put prices about 14% above those national figures.
Is there a mold removal company near me in Bloomington?
Yes. Independent mold inspection and remediation contractors serve Bloomington and nearby California communities. Call the number on this page to be connected and to ask about availability, including same-day inspections.
Is black mold removal in Bloomington different from regular mold removal?
The steps are the same: containment, HEPA air filtration, removal of affected material and cleaning. "Black mold" usually means Stachybotrys chartarum, which grows on wet drywall paper and wood, so affected drywall is normally cut out and replaced, not wiped.
Do I need mold testing before mold removal in Bloomington?
Usually not. The EPA says sampling is generally unnecessary when mold is visible, and the CDC does not recommend routine mold testing. Testing helps when you smell mold but cannot see it, after water damage, and for clearance testing after the job. A typical residential job with a few indoor samples and an outdoor control costs about $300 to $700.
How much humidity causes mold?
Keep indoor relative humidity below 60 percent, and ideally between 30 and 50 percent. The CDC advises no higher than 50 percent. Mold also needs a wet material, so leaks matter more than humidity alone.
Can mold in my home make me sick?
Mold can cause a stuffy nose, sore throat, coughing or wheezing, burning eyes and skin rash. People with asthma, mold allergy, chronic lung disease or weakened immune systems are most affected, and the WHO links damp, moldy buildings to more respiratory symptoms and asthma flare-ups. See a doctor about symptoms and have the mold inspected.
How fast does mold grow after water damage?
Mold can start growing within 24 to 48 hours on wet drywall, carpet and wood. Dry the area quickly, run dehumidifiers and call a professional if materials stay wet longer than two days.
How do I choose a mold removal company in Bloomington?
Ask for proof of insurance, references, a written scope of work that follows IICRC S520, and a plan to fix the moisture source. Be cautious of companies that quote without inspecting, skip containment, or recommend only spraying or "fogging".
Do mold removal companies need certification?
Requirements depend on the state. California has no state license for mold inspectors or remediators and has set no mold exposure limits, according to the Department of Public Health. Ask to see licenses and certificates before hiring.
Is black mold more dangerous than other mold?
Not because of its color. NIOSH says color does not indicate how dangerous a mold is, and the CDC says all molds should be treated the same for health risk and removal. Some Stachybotrys strains can make mycotoxins, but a "toxic mold syndrome" has not been established. Remove any mold you find.
Does insurance cover mold testing or inspection?
Mold testing is usually not covered unless it is part of a covered claim, such as mold after a burst pipe. Ask your insurer before booking, and save the lab report for the claim.
What kills black mold permanently?
Nothing kills it permanently if moisture stays. Dead mold is still an allergen, so the fix is to physically remove it and then stop the moisture. On hard surfaces, detergent and water works. Porous materials like drywall usually have to be replaced.
How much does bathroom mold removal cost?
Most bathroom jobs cost $500 to $2,000, depending on whether drywall, grout or a ceiling must be replaced.
Is mold removal a scam?
No. Professional mold remediation is a real service, but some companies oversell. Look for a pre-job inspection, a written scope, containment and HEPA filtration, a plan to fix the moisture source and clearance testing.
Is mold removal spray dangerous?
Bleach and other biocide sprays can irritate the eyes, lungs and skin, and mixing bleach with ammonia or vinegar creates toxic gas. Ventilate, wear gloves and a mask, and remember spray alone does not fix the moisture problem.
How long does mold remediation take?
Active removal usually takes 1 to 5 days. A small area or bathroom is about 1 day, an attic 1 to 2 days, and a moderate job covering a few rooms 2 to 4 days. Large or whole-house jobs take a week or more, and drying, testing and rebuilding add time.
Sources and Method
Containment tiers, drying times, humidity targets and testing guidance follow the EPA Brief Guide to Mold, Moisture and Your Home, the CDC mold page and NIOSH. Cost ranges are compiled from published cost guides and vary by source. Reviewed 2026-10-18.
Mold Removal Service Area Near Bloomington
We cover Bloomington (ZIP 92316) and surrounding California communities.
Mold removal in nearby cities
- Mold removal in Big Bear Lake, CA
- Mold removal in Blue Jay, CA
- Mold removal in Big Bear City, CA
- Mold removal in Grand Terrace, CA
- Mold removal in Calimesa, CA
- Mold removal in Barstow, CA
- Mold removal in Cedar Glen, CA
- Mold removal in Cedarpines Park, CA
Call for a Free Bloomington Mold Removal Quote: (856) 595-8837